config.yaml

#https://github.com/tsteffek/Ergogen-V4-Migration-Guide
units:
  kx: cx
  ky: cy
  px: 2
  py: 2
points:
  key:
    padding: cy
    tags:
      1u: true
    
          
  zones:
    matrix:
      anchor:
        rotate: 5
      columns:
        outer:
            key:
              column_net: P20
        pinky:
          key:
            column_net: P19
        ring:
          key:
            stagger: 5
            column_net: P18
        middle:
          key:
            stagger: 5
            column_net: P15
        index:
          key:
            stagger: -6
            column_net: P14
        inner:
          key:
            stagger: -2
            column_net: P16
      rows:
        bottom:
          row_net: P7
        home:
          row_net: P6
        top:
          row_net: P5
        num:
          row_net: P4
    thumbfan:
      anchor:
        ref: matrix_inner_bottom
        shift: [-20, -20]
      columns:
        near1:
          key:
            column_net: P20
        near2:
          key:
            column_net: P19
        home:
          rows:
            home:
              column_net: P18
            top:
              column_net: P15
              row_net: P3
          key:
            spread: 21.25
            splay: -20
            origin: [-28, -2]
        far:
          key:
            column_net: P14
            spread: 21.25
            splay: -15
            origin: [-11, -2]
      rows:
        home:
          row_net: P3
      
  rotate: -20
outlines:
    raw: 
      - what: rectangle
        #side: left
        size: [kx + px, ky + py]
        corner: px
        where: true
        
        
    patch_outer:
      - what: polygon
        fillet: 6.35
        points:
          - ref: matrix_outer_num
            shift: [-14,20]
          - ref: matrix_outer_num
            shift: [133,20]
          - ref: thumbfan_home_top
            shift: [10,12]
          - ref: thumbfan_far_home
            shift: [12,20]
          - ref: thumbfan_far_home
            shift: [12.5,-11]
          - ref: thumbfan_near2_home
            shift: [7,-16]
          - ref: thumbfan_near1_home
            shift: [-13,-13]
          - ref: thumbfan_near1_home
            shift: [-13.5,3.5]
          - ref: matrix_outer_bottom
            shift: [-14,-15]

    screw_holes:
      - what: circle
        adjust:
            ref: matrix_outer_num
            shift: [-0.4 cx, .85 cy]
        radius: 1.05
      - what: circle
        adjust:
            ref: matrix_inner_num
            shift: [.33 cx, 0.75 cy]
        radius: 1.05
      - what: circle
        adjust:
            ref: matrix_outer_bottom
            shift: [-.55 cx, -.635 cy]
        radius: 1.05
      - what: circle
        adjust:
            ref: matrix_inner_bottom
            shift: [-.055 cx, -1.85 cy]
        radius: 1.05
      - what: circle
        adjust:
            ref: matrix_middle_bottom
            shift: [.2 cx, -1.2 cy]
        radius: 1.05
      - what: circle
        adjust:
            ref: thumbfan_far_home
            shift: [.4 cx, .96 cy]
        radius: 1.05
      
        
    
        
    keycap_outlines:
      - what: rectangle
        #side: left
        size: [1cx - 0.5, 1cy - 0.5] # Choc keycaps are 17.5 x 16.5
        bound: false    
        #tags: [1u]       
        where: true
    keycap_outlines15:
      - what: rectangle
        #side: left
        size: [1.5cx - 0.5, 1cy - 0.5] # Choc keycaps are 17.5 x 16.5
        bound: false    
        #tags: [15u]     
        where: true  
    preview:
        main:
          what: outline
          name: patch_outer
        switches:
          what: outline
          name: keycap_outlines
          operation: subtract
        holes:
          what: outline
          name: screw_holes
          operation: subtract
    pcb:
        main:
          what: outline
          name: patch_outer
        holes:
          what: outline
          name: screw_holes
          operation: subtract
pcbs:
  top_plate:
    outlines:
      edge:
        outline: preview 
        layer: Edge.Cuts
  board:
    outlines:
      edge:
        outline: pcb
        layer: Edge.Cuts
    footprints:
      choc_hotswap:
        what: choc
        where: true
        params:
          keycaps: true
          reverse: true
          hotswap: true
          from: "{{colrow}}"
          to: "{{column_net}}"
      diode:
        what: diode
        where: true
        params:
          from: "{{colrow}}"
          to: "{{row_net}}"
        adjust:
          shift: [0, -5]
      mcu_l:
        what: promicro_pretty
        params:
          orientation: up
        adjust:
          ref:
            - matrix_inner_top
          shift: [22, -9+1.5*cy]
          rotate: 270
      oled_l:
        what: oled
        adjust:
          ref:
            - matrix_inner_top
          shift: [14.5, -30+1.5 cy]
          rotate: 90
        params:
          CS: P1
          SCL: P2
          SDA: P0
      oled_r:
        what: oled
        adjust:
          ref:
            - matrix_inner_top
          shift: [29, -30+1.5 cy]
          rotate: 270
        params:
          CS: P1
          SCL: P2
          SDA: P0
      #mcu_r:
      #  what: promicro
      #  params:
      #    orientation: down
      #  adjust:
      #    ref:
      #      - matrix_inner_top
      #    shift: [22.5, -12.25]
      #    rotate: 270
      pad_plus:
        what: pad
        adjust:
          ref:
            - matrix_inner_top
          shift: [32, -6]
          rotate: 0
        params:
          net: Bplus
          front: true
          back: true
          width: 1.5
          height: 1.5
          text: "B+"
      pad_minus:
        what: pad
        adjust:
          ref:
            - matrix_inner_top
          shift: [32, -3]
          rotate: 0
        params:
          front: true
          back: true
          width: 1.5
          height: 1.5
          text: "B-"
          net: GND
      # trrs_l:
      #   what: trrs
      #   adjust:
      #     ref:
      #       - matrix_inner_bottom
      #     shift: [32, -15]
      #     rotate: 270
      #   params:
      #     reverse: false
      #     symmetric: false
      #   # The naming of the nets on this footprint is different from the Corne schematics.
      #   nets:
      #     A: ""
      #     B: VCC
      #     C: GND
      #     D: P0
      # trrs_r:
      #   what: trrs
      #   adjust:
      #     ref:
      #       - matrix_inner_bottom
      #     shift: [32, -13]
      #     rotate: 270
      #   params:
      #     reverse: true
      #     symmetric: false
      #   # The naming of the nets on this footprint is different from the Corne schematics.
      #   nets:
      #     A: ""
      #     B: VCC
      #     C: GND
      #     D: P0
      jumper_l:
        what: slider
        adjust:
          ref:
            - matrix_inner_bottom
          shift: [36.5, 0]
          rotate: 270
        params:
          side: B
          from: Bplus
          to: RAW
      jumper_r:
        what: slider
        adjust:
          ref:
            - matrix_inner_bottom
          shift: [36.5, 0]
          rotate: 270
        params:
          side: F
          from: Bplus
          to: RAW
      
      reset_f:
        what: button
        adjust:
          ref:
            - matrix_inner_bottom
          shift: [22.5, 20]
          rotate: 270
        params:
          from: GND
          to: RST
      reset_b:
        what: button
        adjust:
          ref:
            - matrix_inner_bottom
          shift: [22.5, 20]
          rotate: 270
        params:
          from: GND
          to: RST
          side: B
#      info_l:
 #       what: text
  #      adjust:
   #       ref:
    #        - matrix_pinky_bottom
     #     shift: [0.75 kx, 0]
      #  params:
       #   text: "chocBoard"
     #     justify: left
     # info_r:
      #  what: text
       # adjust:
        #  ref:
         #   - matrix_pinky_bottom
        #  shift: [0.75 kx, 0]
       # params:
        #  layer: B.SilkS
         # text: "chocBoard"
          #justify: right mirror